Customer Service & Support: +49 2452 962-450

Business inquiries: +49 2452 962-400

Mon – Fri: 8:00 – 17:00 (CET)

Submerged waste water pump TWP 11025 E
  1. Products & Services
  2. Powertools
  3. Pumps
  4. Submerged pumps
  5. Submerged waste water pumps
  6. TWP 11025 E

Submerged waste water pump TWP 11025 E

Powerful 1,100 W pump with a flow rate of up to 15,000 l/h

Impressive 1,100 watts of power for pumping up to 15,000 litres per hour

TWP 11025 E – Trotec's powerful submerged waste water pump accomplishes virtually any task with flying colours.   Making use of 1,100 watts the pump reliably pumps up to 15,000 litres per hour of clean or contaminated water containing dirt particles sized up to 25 millimetres from a delivery head of up to 11 metres. Hence, it is equally suitable for use in garden ponds, drainage shafts or cisterns as it is for the quick draining of rooms affected by a flood or heavy rainfall. Withdrawing water from lakes, rivers and swimming pools can achieved without difficulty.

A water level of 7 metres is reduced to merely 35 mm before you know it

The robust and compact submerged pump is accommodated in a watertight encapsulated and impact-resistant plastic housing and therefore optimally prepared for underwater application at an immersion depth of up to 7 metres. Starting at a minimum depth of 115 mm the pump operates at a high efficiency level and reliably siphons off waste water to a height of 35 mm.

The TWP 11025 E can not only be used for water withdrawal so as to operate an irrigation system, for water removal after flooding as well as other fields of application involving contaminated water, but is naturally also suitable for transporting clear water. Long-term applications can be realized without difficulty. For the pump comes with both a maintenance-free motor and an integrated thermal protection circuit. The high-quality ceramic face seal and low-wear shaft additionally ensure the extreme durability of this high-performance pump.

Easy to handle – in automatic or manual operation

Via the steplessly lockable float switch the TWP 11025 E can be set to either automatic or manual continuous operation. In automatic mode, the previously defined water level ensures the switch-on/-off of the device. If, however, the float switch is locked horizontally in the position for permanent operation, the device will operate in manual continuous mode.

The elbow position can be flexibly adjusted, as a result it is possible for hoses and pipes to run parallel to the ground. The powerful submerged waste water pump is equipped with universal connections for inner diameters of 25 mm and 32 mm as well as threaded connectors of 1'' and 1½''. A stable carrying handle facilitates site changes and simultaneously serves as suspension for the nylon cord included in the scope of delivery. With it the pump can easily be lowered even to great depths and pulled back up as needed. The connection cable of 10 metres length facilitates the flexible application of the pump.

A suitable pump for any requirement

The submerged waste water pumps TWP 4025 E and TWP 7025 E are our recommendation for smaller delivery heads of up to 5 or 9 metres. They can achieve flow rates of up to 7,500 or 13,000 litres per hour.

Special equipment features of the TWP 11025 E

Particle size: 25 mm
The submerged waste water pump TWP 11025 E conveys heavily contaminated water with particle sizes of up to 25 millimetres.
Ceramic face seal
The high-quality ceramic face seal and a low-wear shaft extend the pump’s lifetime.
Adjustable elbow
The elbow’s position can be freely adjusted, as a result it is possible for hoses and pipes to run parallel to the ground.
Universal connections
Hoses and pipes with an inner diameter of 25 / 32 mm as well as 1’’ / 1½’’ threaded connectors can be flexibly coupled with the pump.
Steplessly adjustable float switch
The float can be fastened in any position, this increases the flexibility when setting the switch-on/switch-off point.
Continuous suction operation to a level of 35 mm
When locking the float switch in horizontal position, the pump operates continually and sucks off the water until only 35 mm remain.
Ergonomic carrying handle
For lowering the pump into the water, the supplied 12 m nylon cord is affixed to the sturdy, ergonomic carrying handle.
Schematic overview
TWP 11025 E at one glance: Combined display of relevant performance values such as the switch-on/switch-off point, delivery head and submersion depth.

TWP 11025 E – a brilliant performance for dirty work

Suitable to an immersion depth of 7 metres
Up to an immersion depth of 7 metres, the submerged pump TWP 11025 E is ideally suited for all applications in contaminated water.
For the application in deep manholes and drainage shafts
With a delivery head of up to 11 m the submerged waste water pump TWP 11025 E is ideally suited for emptying deep manholes or drainage shafts.
Perfect for draining ponds
Water volumes even of large garden ponds can be pumped off quickly and easily at a rate of up to 15,000 litres per hour.
For clear and contaminated water in rain barrels
Pumping off or recirculating the clear or contaminated water from cisterns or rain barrels can be accomplished in a trice.
Technical data in comparison

All submerged pumps in direct comparison:

To find the submerged pump which exactly meets your requirements, please consult the concise overview of all submerged pumps from Trotec, which we're providing to you here so that you can compare them directly to each other.

Models which you do not wish to include in your comparison can be easily dismissed with only one click.

Technical data by comparison

A few practical benefits:

  • Impressive 1,100 watts of power for pumping up to 15,000 litres per hour
  • Maximum delivery head: 11 m
  • Ideally suited for water withdrawal as well as for recirculation and suction of water e.g. for swimming pools, basements, rain barrels, garden ponds, small building pits, flooding
  • For effortless pumping of clear and waste water containing dirt and suspended particles sized up to 25 mm
  • Extremely durable due to ceramic face seal
  • Maintenance-free motor with integrated thermal protection circuit activated by overheating of the device
  • Automatic switch-on/-off due to steplessly adjustable float switch
  • Fixing option for the float switch during automatic operation
  • IPX8 type of protection – protected against the ingress of water upon immersion
  • Universal connection for flexible coupling
  • Large ergonomic carrying handle – suitable for fastening the suspension cord
  • Submerged pump of TÜV-tested quality

All important features at a glance

Clean water
Contaminated water
Powerful 1,100 W motor
Flow rate of 15,000 litres per hour
Delivery head of 11 metres
Immersion depth: 7 metres
Heavily contaminated water with particle sizes of up to 25 millimetres
A water level of no more than 115 mm is sufficient for starting the device
The device continues to operate to a residual water level of 35 mm
Universal connections for inner diameters of 25 mm and 32 mm
Threaded connectors of 1’’, 1¼’’ and 1½’’
Automatic device switch-on/-off
Manual continuous operation
Steplessly lockable float switch
Sturdy, ergonomic carrying handle
Nylon lowering cable of 12 m length
Cable length: 10 metres
For the application in swimming pools
For the application after flooding
For the application in drainage shafts
For the application in garden ponds
Scope of delivery for the submerged clear water pump TWP 11025 E

The submerged pump TWP 11025 E is supplied as complete set including reducer, elbow, a nylon cord of 12 m length and a 10 m power cable.


Delivery head and flow rate

Delivery head and flow rate of the TWP 11025 E

With the TWP 11025 E you are always on the safe side, for this submerged waste water pump is supplied in TÜV-tested quality, thus guaranteeing high value, safety and functionality.

Brand quality plus cost-efficiency

Reliable, powerful and suited for the most challenging fields of application: those are some of the quality features of Trotec's submerged waste water pumps. Thanks to their high capacity they are able to withstand the most extreme conditions. HighPerformance for demanding applications – after all, Trotec stands for brand quality and professional solutions with an excellent value-for-money ratio!

Tested for safety, TÜV GS ID 1419062842

Buy

Technical data

Technical data
General information
  Article number 4.610.000.060
Electrical values
  Mains connection 230 - 240 V, 50 Hz
  Power input [kW] 1.1
Electric connection
  Connection plug CEE 7/4
  Cable length [m] 10
Performance data
  Max. conveying capacity [l/h] 15,000
  Grit of pump [mm] 25
  Max. delivery height [m] 11
  Max. submersion depth [m] 7
  Minimum operating depth [mm] 115
  Max. water level after suction [mm] 35
  Max. water temperature [°C] 35
Safety feature
  Type of protection IPX8
  Protection class I
Functions and features
  On/off switch (float switch) Automatic
  Switch-on point float switch [mm] 600
  Switch-off point float switch [mm] 180
  Thermal overload protection
  Backflow preventer
  Stainless steel screws
  Suitable for both permanent operation (>10h) or salt-water operation
Housing design
  Plastics
Accessories scope of delivery
  Adapter
  Hose connection (inner diameter) 25 / 32 mm
  Threaded connection 1" , 1 ½"
  Backflow preventer
Dimensions
  Length (packaging excluded) [mm] 220
  Width (packaging excluded) [mm] 160
  Height (packaging excluded) [mm] 355
Weight
  (packaging excluded) [kg] 6

 standard equipment

 optionally available

 not available

Alternative products

Loading...

Accessories

Loading...

Downloads

Loading...